"人机环管"在煤矿供电安全管理中的应用

制定供电过程中消除安全隐患的针对性措施,可以为矿井安全生产提供必要保障。为探究煤矿供电管理中安全隐患的具体分析方法,首先介绍“人机环管”管理体系的建立过程和核心内容,接着以“人机环管”的管理方法分析了供电管理中的普遍问题。在分析供电管理中的具体问题时,分别得出了“人”“机”“环”“管”4方面的具体措施。分析认为,“人机环管”方法可以有效查找出存在的安全隐患,进而保证煤矿供电系统的安全可靠。     

Design of Feedback Shift Register of Against Power Analysis Attack

Stream ciphers based on linear feedback shift register (LFSR) are suitable for constrained environments, such as satellite communications, radio frequency identification devices tag, sensor networks and Internet of Things, due to its simple hardware structures, high speed encryption and lower power consumption. LFSR, as a cryptographic primitive, has been used to generate a maximum period sequence. Because the switching of the status bits is regular, the power consumption of the LFSR is correlated in a linear way. As a result, the power consumption characteristics of stream cipher based on LFSR are vulnerable to leaking initialization vectors under the power attacks. In this paper, a new design of LFSR against power attacks is proposed. The power consumption characteristics of LFSR can be masked by using an additional LFSR and confused by adding a new filter Boolean function and a flip-flop. The design method has been implemented easily by circuits in this new design in comparison with the others.     

Stabilizing temperature-capacitance dependence of (Sr,Pb, Bi)TiO3-Bi4Ti3O12 solutions for energy storage

(1-x)Sr_0.7Pb_0.15Bi_0.1TiO₃-xBi₄Ti₃O₁₂ ((1-x)SPBT-xBIT, x = 0-0.125) bulk ceramics were developed and calcined via the solid-state method, aimed at the application of pulsed power capacitors. The phase structures, temperature stability, hysteresis loop, and discharge properties were systematically investigated. Considering both the temperature stability and dielectric properties, 0.925SPBT-0.075BIT bulk ceramics with a capacitance variation satisfying the X7R specification were developed for pulsed power capacitors. The energy storage density was 0.252 J/cm³, and the ceramics showed high temperature stability at 80 kV/cm. The discharge current waveforms of the 0.925SPBT-0.075BIT ceramics were recorded. A high discharge power density of approximately 1.01 × 10⁸ W/kg with an 8 Ω load resistor and short discharge period of 84 ns were achieved at 50 kV/cm. The good temperature stability properties and high power density show that the 0.925SPBT-0.075BIT ceramics are well suited for pulsed power capacitors with a wide temperature range.     

Artificial bee colony based algorithm for maximum power point tracking (MPPT) for PV systems operating under partial shaded conditions

Artificial bee colony (ABC) algorithm has several characteristics that make it more attractive than other bio-inspired methods. Particularly, it is simple, it uses fewer control parameters and its convergence is independent of the initial conditions. In this paper, a novel artificial bee colony based maximum power point tracking algorithm (MPPT) is proposed. The developed algorithm, does not allow only overcoming the common drawback of the conventional MPPT methods, but it gives a simple and a robust MPPT scheme. A co-simulation methodology, combining Matlab/Simulink™ and Cadence/Pspice™, is used to verify the effectiveness of the proposed method and compare its performance, under dynamic weather conditions, with that of the Particle Swarm Optimization (PSO) based MPPT algorithm. Moreover, a laboratory setup has been realized and used to experimentally validate the proposed ABC-based MPPT algorithm. Simulation and experimental results have shown the satisfactory performance of the proposed approach.     

Study on maximum power point tracking of photovoltaic array in irregular shadow

Traditional maximum power point tracking (MPPT) methods can hardly find global maximum power point (MPP) because output characteristics curve of photovoltaic (PV) array may have multi local maximum power points in irregular shadow, and thus easily fall into the local maximum power point. To address this drawback, Considering that sliding mode variable structure (SMVS) control strategy have such advantages as simple structure, fast response and strong robustness, and P&O method have the advantages of simple principle and convenient implementation, so a new algorithm combining SMVS control method and P&O method is proposed, besides, PI controller is applied to reduce system chattering caused by switching sliding surface. It is applied to MPPT control of PV array in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verity the rationality of the proposed algorithm, the experimental circuit is built, which achieves MPPT control by means of the proposed algorithm and P&O method. The experimental results show that compared with the traditional P&O algorithm, the proposed algorithm can fast track the global MPP, tracking speed increases by 60% and the relative error decreased by 20%. Moreover, the system becomes more stable near the MPP, the fluctuations of output power is greatly reduced, and thus make full use of solar energy.     

A probabilistic load shedding concept considering highly volatile local generation

Automatic load shedding is the ultimate countermeasure against imbalance in a power system and can effectively help preventing large blackouts. Taking into account a high penetration of renewable energy sources (RES) in the distribution grid, a clear distinction between load and generation at the PCC becomes increasingly more difficult. For that reason an adaptation of frequency relay parameters and their locations of installation are necessary. In Europe this is rest on a multi-step plan based on values such as the yearly peak load. In this paper a novel probabilistic method for automatic load shedding is presented that uses the average values instead of peak values for load shedding. Its applicability is verified by a dynamic power system model that was developed to compare the classical and novel probabilistic load shedding principle. The method is verified using data from a German TSO.     

Study of MW-scale biogas-fed SOFC-WGS-TSA-PEMFC hybrid power technology as distributed energy system: Thermodynamic,exergetic and thermo-economic evaluation

Advanced biogas power generation technology has been attracting attentions, which contributes to the waste disposal and the mitigation of greenhouse gas emissions. This work proposes and models a novel biogas-fed hybrid power generation system consisting of solid oxide fuel cell, water gas shift reaction, thermal swing adsorption and proton exchange membrane fuel cell (SOFC-WGS-TSA-PEMFC). The thermodynamic, exergetic, and thermo-economic analyses of this hybrid system for power generation were conducted to comprehensively evaluate its performance. It was found that the novel biogas-fed hybrid system has a gross energy conversion efficiency of 68.63% and exergy efficiency of 65.36%, indicating high efficiency for this kind of hybrid power technology. The market sensitivity analysis showed that the hybrid system also has a low sensitivity to market price fluctuation. Under the current subsidy level for the distributed biogas power plant, the levelized cost of energy can be lowered to 0.02942 $/kWh for a 1 MW scale system. Accordingly, the payback period and annual return on investment can reach 1.4 year and about 20%, respectively. These results reveal that the proposed hybrid system is promising and economically feasible as a distributed power plant, especially for the small power scale (no more than 2 MW).     

LTE系统多小区上行联合功控算法

针对传统的小区内开环功率控制算法通常以提升本小区的吞吐量性能为目标，忽略了当前小区用户对邻小区用户同频干扰的问题，为提升边缘用户性能的同时兼顾系统整体性能，提出了一种LTE系统小区间上行联合功率控制（UJPC）算法。该算法采用单基站三扇区为系统模型，以最优化系统吞吐量比例公平函数为目标，首先根据最小信干噪比（SINR）约束值和用户最大发射功率这两个约束条件得到相应的数学优化模型，然后采用连续凸近似的方法求解优化问题得出各个基站所管辖的小区内所有用户的最优发射功率。仿真结果表明，与基准的开环功控方案相比，联合功控方案在保证系统平均频谱利用率的情况下能够较大幅度地提高小区边缘频谱利用率，其最佳性能增益能达到50%。     

园区多能互补供能系统设计方法研究

为提高园区多能互补工程的能源综合利用效率及整体效益，对供能系统设计中的负荷统计、逐时负荷匹配、供能系统、设备选型、容量配置及运行策略等问题进行了分析和总结，提出园区多能互补供能系统设计的基本流程与方法，可为园区多能互补供能系统的设计提供参考。     

基于热负荷自动调节的延迟焦化加热炉三点注汽量智能优化

针对国内某炼油厂延迟焦化加热炉三点注汽问题，采用热负荷自动调节的算法进行了研究。运用该模型方法，分析了三点注汽量对加热炉热负荷和炉管结焦系数的影响，发现三点注汽量的改变均会对热负荷和炉管结焦系数产生影响，主要表现为提高注汽量将会提高热负荷，同时降低结焦系数；第1点注汽量和第2点注汽量对热负荷和结焦系数的影响较强，第3点注汽量对热负荷和结焦系数的影响较弱。在实际操作中，加热炉中的结焦程度既不能太强也不能太弱，合适的结焦系数能够保证正常开工周期里炉管不结焦，也能保证瓦斯、注汽量等参数的合理分配。通过对热负荷、注汽量的智能分配，可得到不同原料油加工负荷条件下更加合理的装置运行方案。